aDriv4 website!

Linux ircpanel.novinhost.org 4.18.0-553.34.1.lve.el8.x86_64 #1 SMP Thu Jan 9 16:30:32 UTC 2025 x86_64
Apache
213.232.124.78

File Name : dracut-lib.sh

#!/bin/sh

export DRACUT_SYSTEMD
export NEWROOT
if [ -n "$NEWROOT" ]; then
    [ -d $NEWROOT ] || mkdir -p -m 0755 $NEWROOT
fi

if ! [ -d /run/initramfs ]; then
    mkdir -p -m 0755 /run/initramfs/log
    ln -sfn /run/initramfs/log /var/log
fi

[ -d /run/lock ] || mkdir -p -m 0755 /run/lock
[ -d /run/log ] || mkdir -p -m 0755 /run/log

debug_off() {
    set +x
}

debug_on() {
    [ "$RD_DEBUG" = "yes" ] && set -x
}

# returns OK if $1 contains literal string $2 (and isn't empty)
strstr() {
    [ "${1##*"$2"*}" != "$1" ]
}

# returns OK if $1 matches (completely) glob pattern $2
# An empty $1 will not be considered matched, even if $2 is * which technically
# matches; as it would match anything, it's not an interesting case.
strglob() {
    [ -n "$1" -a -z "${1##$2}" ]
}

# returns OK if $1 contains (anywhere) a match of glob pattern $2
# An empty $1 will not be considered matched, even if $2 is * which technically
# matches; as it would match anything, it's not an interesting case.
strglobin() {
    [ -n "$1" -a -z "${1##*$2*}" ]
}

# returns OK if $1 contains literal string $2 at the beginning, and isn't empty
str_starts() {
    [ "${1#"$2"*}" != "$1" ]
}

# returns OK if $1 contains literal string $2 at the end, and isn't empty
str_ends() {
    [ "${1%*"$2"}" != "$1" ]
}

trim() {
    local var="$*"
    var="${var#"${var%%[![:space:]]*}"}"   # remove leading whitespace characters
    var="${var%"${var##*[![:space:]]}"}"   # remove trailing whitespace characters
    printf "%s" "$var"
}

if [ -z "$DRACUT_SYSTEMD" ]; then

warn() {
        check_quiet
        echo "<28>dracut Warning: $*" > /dev/kmsg
        echo "dracut Warning: $*" >&2
    }

info() {
        check_quiet
        echo "<30>dracut: $*" > /dev/kmsg
        [ "$DRACUT_QUIET" != "yes" ] && \
            echo "dracut: $*" >&2
    }

else

warn() {
        echo "Warning: $*" >&2
    }

info() {
        echo "$*"
    }

vwarn() {
    while read line || [ -n "$line" ]; do
        warn $line;
    done
}

vinfo() {
    while read line || [ -n "$line" ]; do
        info $line;
    done
}

# replaces all occurrences of 'search' in 'str' with 'replacement'
#
# str_replace str search replacement
#
# example:
# str_replace '  one two  three  ' ' ' '_'
str_replace() {
    local in="$1"; local s="$2"; local r="$3"
    local out=''

while strstr "${in}" "$s"; do
        chop="${in%%"$s"*}"
        out="${out}${chop}$r"
        in="${in#*"$s"}"
    done
    echo "${out}${in}"
}

killall_proc_mountpoint() {
    local _pid
    local _t
    local _killed=0
    for _pid in /proc/*; do
        _pid=${_pid##/proc/}
        case $_pid in
            *[!0-9]*) continue;;
        esac
        [ -e "/proc/$_pid/exe" ] || continue
        [ -e "/proc/$_pid/root" ] || continue
        if strstr "$(ls -l -- "/proc/$_pid" "/proc/$_pid/fd" 2>/dev/null)" "$1" ; then
            kill -9 "$_pid"
            _killed=1
        fi
    done
    return $_killed
}

getcmdline() {
    local _line
    local _i
    local CMDLINE_ETC_D
    local CMDLINE_ETC
    local CMDLINE_PROC
    unset _line

if [ -e /etc/cmdline ]; then
        while read -r _line || [ -n "$_line" ]; do
            CMDLINE_ETC="$CMDLINE_ETC $_line";
        done </etc/cmdline;
    fi
    for _i in /etc/cmdline.d/*.conf; do
        [ -e "$_i" ] || continue
        while read -r _line || [ -n "$_line" ]; do
            CMDLINE_ETC_D="$CMDLINE_ETC_D $_line";
        done <"$_i";
    done
    if [ -e /proc/cmdline ]; then
        while read -r _line || [ -n "$_line" ]; do
            CMDLINE_PROC="$CMDLINE_PROC $_line"
        done </proc/cmdline;
    fi
    CMDLINE="$CMDLINE_ETC_D $CMDLINE_ETC $CMDLINE_PROC"
    printf "%s" "$CMDLINE"
}

_dogetarg() {
    local _o _val _doecho
    unset _val
    unset _o
    unset _doecho
    CMDLINE=$(getcmdline)

for _o in $CMDLINE; do
        if [ "${_o%%=*}" = "${1%%=*}" ]; then
            if [ -n "${1#*=}" -a "${1#*=*}" != "${1}" ]; then
                # if $1 has a "=<value>", we want the exact match
                if [ "$_o" = "$1" ]; then
                    _val="1";
                    unset _doecho
                fi
                continue
            fi

if [ "${_o#*=}" = "$_o" ]; then
                # if cmdline argument has no "=<value>", we assume "=1"
                _val="1";
                unset _doecho
                continue
            fi

_val="${_o#*=}"
            _doecho=1
        fi
    done
    if [ -n "$_val" ]; then
        [ "x$_doecho" != "x" ] && echo "$_val";
        return 0;
    fi
    return 1;
}

getarg() {
    debug_off
    local _deprecated _newoption
    while [ $# -gt 0 ]; do
        case $1 in
            -d) _deprecated=1; shift;;
            -y) if _dogetarg $2 >/dev/null; then
                    if [ "$_deprecated" = "1" ]; then
                        [ -n "$_newoption" ] && warn "Kernel command line option '$2' is deprecated, use '$_newoption' instead." || warn "Option '$2' is deprecated."
                    fi
                    echo 1
                    debug_on
                    return 0
                fi
                _deprecated=0
                shift 2;;
            -n) if _dogetarg $2 >/dev/null; then
                    echo 0;
                    if [ "$_deprecated" = "1" ]; then
                        [ -n "$_newoption" ] && warn "Kernel command line option '$2' is deprecated, use '$_newoption=0' instead." || warn "Option '$2' is deprecated."
                    fi
                    debug_on
                    return 1
                fi
                _deprecated=0
                shift 2;;
            *)  if [ -z "$_newoption" ]; then
                    _newoption="$1"
                fi
                if _dogetarg $1; then
                    if [ "$_deprecated" = "1" ]; then
                        [ -n "$_newoption" ] && warn "Kernel command line option '$1' is deprecated, use '$_newoption' instead." || warn "Option '$1' is deprecated."
                    fi
                    debug_on
                    return 0;
                fi
                _deprecated=0
                shift;;
        esac
    done
    debug_on
    return 1
}

# getargbool <defaultval> <args...>
# False if "getarg <args...>" returns "0", "no", or "off".
# True if getarg returns any other non-empty string.
# If not found, assumes <defaultval> - usually 0 for false, 1 for true.
# example: getargbool 0 rd.info
#   true: rd.info, rd.info=1, rd.info=xxx
#   false: rd.info=0, rd.info=off, rd.info not present (default val is 0)
getargbool() {
    local _b
    unset _b
    local _default
    _default="$1"; shift
    _b=$(getarg "$@")
    [ $? -ne 0 -a -z "$_b" ] && _b="$_default"
    if [ -n "$_b" ]; then
        [ $_b = "0" ] && return 1
        [ $_b = "no" ] && return 1
        [ $_b = "off" ] && return 1
    fi
    return 0
}

isdigit() {
    case "$1" in
        *[!0-9]*|"") return 1;;
    esac

return 0
}

# getargnum <defaultval> <minval> <maxval> <arg>
# Will echo the arg if it's in range [minval - maxval].
# If it's not set or it's not valid, will set it <defaultval>.
# Note all values are required to be >= 0 here.
# <defaultval> should be with [minval -maxval].
getargnum() {
    local _b
    unset _b
    local _default _min _max
    _default="$1"; shift
    _min="$1"; shift
    _max="$1"; shift
    _b=$(getarg "$1")
    [ $? -ne 0 -a -z "$_b" ] && _b=$_default
    if [ -n "$_b" ]; then
        isdigit "$_b" && _b=$(($_b)) && \
          [ $_b -ge $_min ] && [ $_b -le $_max ] && echo $_b && return
    fi
    echo $_default
}

_dogetargs() {
    debug_off
    local _o _found _key
    unset _o
    unset _found
    CMDLINE=$(getcmdline)
    _key="$1"
    set --
    for _o in $CMDLINE; do
        if [ "$_o" = "$_key" ]; then
            _found=1;
        elif [ "${_o%%=*}" = "${_key%=}" ]; then
            [ -n "${_o%%=*}" ] && set -- "$@" "${_o#*=}";
            _found=1;
        fi
    done
    if [ -n "$_found" ]; then
        [ $# -gt 0 ] && printf '%s' "$*"
        return 0
    fi
    return 1;
}

getargs() {
    debug_off
    local _val _i _args _gfound _deprecated
    unset _val
    unset _gfound
    _newoption="$1"
    _args="$@"
    set --
    for _i in $_args; do
        if [ "$_i" = "-d" ]; then
            _deprecated=1
            continue
        fi
        _val="$(_dogetargs $_i)"
        if [ $? -eq 0 ]; then
            if [ "$_deprecated" = "1" ]; then
                [ -n "$_newoption" ] && warn "Option '$_i' is deprecated, use '$_newoption' instead." || warn "Option $_i is deprecated!"
            fi
            _gfound=1
        fi
        [ -n "$_val" ] && set -- "$@" "$_val"
        _deprecated=0
    done
    if [ -n "$_gfound" ]; then
        if [ $# -gt 0 ]; then
            printf '%s' "$*"
        fi
        debug_on
        return 0
    fi
    debug_on
    return 1;
}

# Prints value of given option.  If option is a flag and it's present,
# it just returns 0.  Otherwise 1 is returned.
# $1 = options separated by commas
# $2 = option we are interested in
#
# Example:
# $1 = cipher=aes-cbc-essiv:sha256,hash=sha256,verify
# $2 = hash
# Output:
# sha256
getoptcomma() {
    local line=",$1,"; local opt="$2"; local tmp

case "${line}" in
        *,${opt}=*,*)
            tmp="${line#*,${opt}=}"
            echo "${tmp%%,*}"
            return 0
            ;;
        *,${opt},*) return 0;;
    esac
    return 1
}

# Splits given string 'str' with separator 'sep' into variables 'var1', 'var2',
# 'varN'.  If number of fields is less than number of variables, remaining are
# not set.  If number of fields is greater than number of variables, the last
# variable takes remaining fields.  In short - it acts similary to 'read'.
#
# splitsep sep str var1 var2 varN
#
# example:
#   splitsep ':' 'foo:bar:baz' v1 v2
# in result:
#   v1='foo', v2='bar:baz'
#
# TODO: ':' inside fields.
splitsep() {
    debug_off
    local sep="$1"; local str="$2"; shift 2
    local tmp

while [ -n "$str" -a "$#" -gt 1 ]; do
        tmp="${str%%$sep*}"
        eval "$1='${tmp}'"
        str="${str#"$tmp"}"
        str="${str#$sep}"
        shift
    done
    [ -n "$str" -a -n "$1" ] && eval "$1='$str'"
    debug_on
    return 0
}

setdebug() {
    [ -f /usr/lib/initrd-release ] || return
    if [ -z "$RD_DEBUG" ]; then
        if [ -e /proc/cmdline ]; then
            RD_DEBUG=no
            if getargbool 0 rd.debug -d -y rdinitdebug -d -y rdnetdebug; then
                RD_DEBUG=yes
                [ -n "$BASH" ] && \
                    export PS4='${BASH_SOURCE}@${LINENO}(${FUNCNAME[0]}): ';
           fi
        fi
        export RD_DEBUG
    fi
    debug_on
}

setdebug

source_all() {
    local f
    local _dir
    _dir=$1; shift
    [ "$_dir" ] && [  -d "/$_dir" ] || return
    for f in "/$_dir"/*.sh; do [ -e "$f" ] && . "$f" "$@"; done
}

hookdir=/lib/dracut/hooks
export hookdir

source_hook() {
    local _dir
    _dir=$1; shift
    source_all "/lib/dracut/hooks/$_dir" "$@"
}

check_finished() {
    local f
    for f in $hookdir/initqueue/finished/*.sh; do
        [ "$f" = "$hookdir/initqueue/finished/*.sh" ] && return 0
        { [ -e "$f" ] && ( . "$f" ) ; } || return 1
    done
    return 0
}

source_conf() {
    local f
    [ "$1" ] && [  -d "/$1" ] || return
    for f in "/$1"/*.conf; do [ -e "$f" ] && . "$f"; done
}

die() {
    {
        echo "<24>dracut: FATAL: $*";
        echo "<24>dracut: Refusing to continue";
    } > /dev/kmsg

{
        echo "warn dracut: FATAL: \"$*\"";
        echo "warn dracut: Refusing to continue";
    } >> $hookdir/emergency/01-die.sh
    [ -d /run/initramfs ] || mkdir -p -- /run/initramfs

> /run/initramfs/.die

if getargbool 0 "rd.shell"; then
        emergency_shell
    else
        source_hook "shutdown-emergency"
    fi

if [ -n "$DRACUT_SYSTEMD" ]; then
        systemctl --no-block --force halt
    fi

exit 1
}

check_quiet() {
    if [ -z "$DRACUT_QUIET" ]; then
        DRACUT_QUIET="yes"
        getargbool 0 rd.info -d -y rdinfo && DRACUT_QUIET="no"
        getargbool 0 rd.debug -d -y rdinitdebug && DRACUT_QUIET="no"
        getarg quiet || DRACUT_QUIET="yes"
        a=$(getarg loglevel=)
        [ -n "$a" ] && [ $a -ge 28 ] && DRACUT_QUIET="yes"
        export DRACUT_QUIET
    fi
}

check_occurances() {
    # Count the number of times the character $ch occurs in $str
    # Return 0 if the count matches the expected number, 1 otherwise
    local str="$1"
    local ch="$2"
    local expected="$3"
    local count=0

while [ "${str#*$ch}" != "${str}" ]; do
        str="${str#*$ch}"
        count=$(( $count + 1 ))
    done

[ $count -eq $expected ]
}

incol2() {
    debug_off
    local dummy check;
    local file="$1";
    local str="$2";

[ -z "$file" ] && return 1;
    [ -z "$str"  ] && return 1;

while read dummy check restofline || [ -n "$check" ]; do
        if [ "$check" = "$str" ]; then
            debug_on
            return 0
        fi
    done < $file
    debug_on
    return 1
}

udevsettle() {
    [ -z "$UDEVVERSION" ] && export UDEVVERSION=$(udevadm --version | { read v _ ; echo $v ; })

if [ $UDEVVERSION -ge 143 ]; then
        udevadm settle --exit-if-exists=$hookdir/initqueue/work $settle_exit_if_exists
    else
        udevadm settle --timeout=30
    fi
}

udevproperty() {
    [ -z "$UDEVVERSION" ] && export UDEVVERSION=$(udevadm --version | { read v _ ; echo $v ; })

if [ $UDEVVERSION -ge 143 ]; then
        for i in "$@"; do udevadm control --property=$i; done
    else
        for i in "$@"; do udevadm control --env=$i; done
    fi
}

find_mount() {
    local dev mnt etc wanted_dev
    wanted_dev="$(readlink -e -q $1)"
    while read dev mnt etc || [ -n "$dev" ]; do
        [ "$dev" = "$wanted_dev" ] && echo "$dev" && return 0
    done < /proc/mounts
    return 1
}

# usage: ismounted <mountpoint>
# usage: ismounted /dev/<device>
if command -v findmnt >/dev/null; then
    ismounted() {
        findmnt "$1" > /dev/null 2>&1
    }
else
    ismounted() {
        if [ -b "$1" ]; then
            find_mount "$1" > /dev/null && return 0
            return 1
        fi

while read a m a || [ -n "$m" ]; do
            [ "$m" = "$1" ] && return 0
        done < /proc/mounts
        return 1
    }
fi

# root=nfs:[<server-ip>:]<root-dir>[:<nfs-options>]
# root=nfs4:[<server-ip>:]<root-dir>[:<nfs-options>]
nfsroot_to_var() {
    # strip nfs[4]:
    local arg="$@:"
    nfs="${arg%%:*}"
    arg="${arg##$nfs:}"

# check if we have a server
    if strstr "$arg" ':/' ; then
        server="${arg%%:/*}"
        arg="/${arg##*:/}"
    fi

path="${arg%%:*}"

# rest are options
    options="${arg##$path}"
    # strip leading ":"
    options="${options##:}"
    # strip  ":"
    options="${options%%:}"

# Does it really start with '/'?
    [ -n "${path%%/*}" ] && path="error";

#Fix kernel legacy style separating path and options with ','
    if [ "$path" != "${path#*,}" ] ; then
        options=${path#*,}
        path=${path%%,*}
    fi
}

# Create udev rule match for a device with its device name, or the udev property
# ID_FS_UUID or ID_FS_LABEL
#
# example:
#   udevmatch LABEL=boot
# prints:
#   ENV{ID_FS_LABEL}="boot"
#
# TODO: symlinks
udevmatch() {
    case "$1" in
    UUID=????????-????-????-????-????????????|LABEL=*|PARTLABEL=*|PARTUUID=????????-????-????-????-????????????)
        printf 'ENV{ID_FS_%s}=="%s"' "${1%%=*}" "${1#*=}"
        ;;
    UUID=*)
        printf 'ENV{ID_FS_UUID}=="%s*"' "${1#*=}"
        ;;
    PARTUUID=*)
        printf 'ENV{ID_FS_PARTUUID}=="%s*"' "${1#*=}"
        ;;
    /dev/?*) printf -- 'KERNEL=="%s"' "${1#/dev/}" ;;
    *) return 255 ;;
    esac
}

# Prints unique path for potential file inside specified directory.  It consists
# of specified directory, prefix and number at the end which is incremented
# until non-existing file is found.
#
# funiq dir prefix
#
# example:
# # ls /mnt
# cdrom0 cdrom1
#
# # funiq /mnt cdrom
# /mnt/cdrom2
funiq() {
    local dir="$1"; local prefix="$2"
    local i=0

[ -d "${dir}" ] || return 1

while [ -e "${dir}/${prefix}$i" ]; do
        i=$(($i+1)) || return 1
    done

echo "${dir}/${prefix}$i"
}

# Creates unique directory and prints its path.  It's using funiq to generate
# path.
#
# mkuniqdir subdir new_dir_name
mkuniqdir() {
    local dir="$1"; local prefix="$2"
    local retdir; local retdir_new

[ -d "${dir}" ] || mkdir -m 0755 -p "${dir}" || return 1

retdir=$(funiq "${dir}" "${prefix}") || return 1
    until mkdir -m 0755 "${retdir}" 2>/dev/null; do
        retdir_new=$(funiq "${dir}" "${prefix}") || return 1
        [ "$retdir_new" = "$retdir" ] && return 1
        retdir="$retdir_new"
    done

echo "${retdir}"
}

# Copy the contents of SRC into DEST, merging the contents of existing
# directories (kinda like rsync, or cpio -p).
# Creates DEST if it doesn't exist. Overwrites files with the same names.
#
# copytree SRC DEST
copytree() {
    local src="$1" dest="$2"
    mkdir -p "$dest"; dest=$(readlink -e -q "$dest")
    ( cd "$src"; cp -af . -t "$dest" )
}

# Evaluates command for UUIDs either given as arguments for this function or all
# listed in /dev/disk/by-uuid.  UUIDs doesn't have to be fully specified.  If
# beginning is given it is expanded to all matching UUIDs.  To pass full UUID to
# your command use '$___' as a place holder.  Remember to escape '$'!
#
# foreach_uuid_until [ -p prefix ] command UUIDs
#
# prefix - string to put just before $___
# command - command to be evaluated
# UUIDs - list of UUIDs separated by space
#
# The function returns after *first successful evaluation* of the given command
# with status 0.  If evaluation fails for every UUID function returns with
# status 1.
#
# Example:
# foreach_uuid_until "mount -U \$___ /mnt; echo OK; umount /mnt" \
#       "01234 f512 a235567f-12a3-c123-a1b1-01234567abcb"
foreach_uuid_until() (
    cd /dev/disk/by-uuid

[ "$1" = -p ] && local prefix="$2" && shift 2
    local cmd="$1"; shift; local uuids_list="$*"
    local uuid; local full_uuid; local ___

[ -n "${cmd}" ] || return 1

for uuid in ${uuids_list:-*}; do
        for full_uuid in ${uuid}*; do
            [ -e "${full_uuid}" ] || continue
            ___="${prefix}${full_uuid}"
            eval ${cmd} && return 0
        done
    done

return 1
)

# Get kernel name for given device.  Device may be the name too (then the same
# is returned), a symlink (full path), UUID (prefixed with "UUID=") or label
# (prefixed with "LABEL=").  If just a beginning of the UUID is specified or
# even an empty, function prints all device names which UUIDs match - every in
# single line.
#
# NOTICE: The name starts with "/dev/".
#
# Example:
#   devnames UUID=123
# May print:
#   /dev/dm-1
#   /dev/sdb1
#   /dev/sdf3
devnames() {
    local dev="$1"; local d; local names

case "$dev" in
    UUID=*)
        dev="$(foreach_uuid_until '! blkid -U $___' "${dev#UUID=}")" \
            && return 255
        [ -z "$dev" ] && return 255
        ;;
    LABEL=*) dev="$(blkid -L "${dev#LABEL=}")" || return 255 ;;
    /dev/?*) ;;
    *) return 255 ;;
    esac

for d in $dev; do
        names="$names
$(readlink -e -q "$d")" || return 255
    done

echo "${names#
}"
}

usable_root() {
    local _i

[ -d "$1" ] || return 1

for _i in "$1"/usr/lib*/ld-*.so "$1"/lib*/ld-*.so; do
        [ -e "$_i" ] && return 0
    done

for _i in proc sys dev; do
        [ -e "$1"/$_i ] || return 1
    done

return 0
}

inst_hook() {
    local _hookname _unique _name _job _exe
    while [ $# -gt 0 ]; do
        case "$1" in
            --hook)
                _hookname="/$2";shift;;
            --unique)
                _unique="yes";;
            --name)
                _name="$2";shift;;
            *)
                break;;
        esac
        shift
    done

if [ -z "$_unique" ]; then
        _job="${_name}$$"
    else
        _job="${_name:-$1}"
        _job=${_job##*/}
    fi

_exe=$1
    shift

[ -x "$_exe" ] || _exe=$(command -v $_exe)

if [ -n "$onetime" ]; then
        {
            echo '[ -e "$_job" ] && rm -f -- "$_job"'
            echo "$_exe $@"
        } > "/tmp/$$-${_job}.sh"
    else
        echo "$_exe $@" > "/tmp/$$-${_job}.sh"
    fi

mv -f "/tmp/$$-${_job}.sh" "$hookdir/${_hookname}/${_job}.sh"
}

# inst_mount_hook <mountpoint> <prio> <name> <script>
#
# Install a mount hook with priority <prio>,
# which executes <script> as soon as <mountpoint> is mounted.
inst_mount_hook() {
    local _prio="$2" _jobname="$3" _script="$4"
    local _hookname="mount-$(str_replace "$1" '/' '\\x2f')"
    [ -d "$hookdir/${_hookname}" ] || mkdir -p "$hookdir/${_hookname}"
    inst_hook --hook "$_hookname" --unique --name "${_prio}-${_jobname}" "$_script"
}

# add_mount_point <dev> <mountpoint> <filesystem> <fsopts>
#
# Mount <dev> on <mountpoint> with <filesystem> and <fsopts>
# and call any mount hooks, as soon, as it is mounted
add_mount_point() {
    local _dev="$1" _mp="$2" _fs="$3" _fsopts="$4"
    local _hookname="mount-$(str_replace "$2" '/' '\\x2f')"
    local _devname="dev-$(str_replace "$1" '/' '\\x2f')"
    echo "$_dev $_mp $_fs $_fsopts 0 0" >> /etc/fstab

exec 7>/etc/udev/rules.d/99-mount-${_devname}.rules
    echo 'SUBSYSTEM!="block", GOTO="mount_end"' >&7
    echo 'ACTION!="add|change", GOTO="mount_end"' >&7
    if [ -n "$_dev" ]; then
        udevmatch "$_dev" >&7 || {
            warn "add_mount_point dev=$_dev incorrect!"
            continue
        }
        printf ', ' >&7
    fi

{
        printf -- 'RUN+="%s --unique --onetime ' $(command -v initqueue)
        printf -- '--name mount-%%k '
        printf -- '%s %s"\n' "$(command -v mount_hook)" "${_mp}"
    } >&7
    echo 'LABEL="mount_end"' >&7
    exec 7>&-
}

# wait_for_mount <mountpoint>
#
# Installs a initqueue-finished script,
# which will cause the main loop only to exit,
# if <mountpoint> is mounted.
wait_for_mount()
{
    local _name
    _name="$(str_replace "$1" '/' '\\x2f')"
    printf '. /lib/dracut-lib.sh\nismounted "%s"\n' $1 \
        >> "$hookdir/initqueue/finished/ismounted-${_name}.sh"
    {
        printf 'ismounted "%s" || ' $1
        printf 'warn "\"%s\" is not mounted"\n' $1
    } >> "$hookdir/emergency/90-${_name}.sh"
}

# get a systemd-compatible unit name from a path
# (mimicks unit_name_from_path_instance())
dev_unit_name()
{
    local dev="$1"

if command -v systemd-escape >/dev/null; then
        systemd-escape -p -- "$dev"
        return
    fi

if [ "$dev" = "/" -o -z "$dev" ]; then
        printf -- "-"
        exit 0
    fi

dev="${1%%/}"
    dev="${dev##/}"
    dev="$(str_replace "$dev" '\' '\x5c')"
    dev="$(str_replace "$dev" '-' '\x2d')"
    if [ "${dev##.}" != "$dev" ]; then
        dev="\x2e${dev##.}"
    fi
    dev="$(str_replace "$dev" '/' '-')"

printf -- "%s" "$dev"
}

# set_systemd_timeout_for_dev <dev>
# Set 'rd.timeout' as the systemd timeout for <dev>

set_systemd_timeout_for_dev()
{
    local _name
    local _needreload
    local _noreload
    local _timeout

if [ "$1" = "-n" ]; then
        _noreload=1
        shift
    fi

_timeout=$(getarg rd.timeout)
    _timeout=${_timeout:-0}

if [ -n "$DRACUT_SYSTEMD" ]; then
        _name=$(dev_unit_name "$1")
        if ! [ -L ${PREFIX}/etc/systemd/system/initrd.target.wants/${_name}.device ]; then
            [ -d ${PREFIX}/etc/systemd/system/initrd.target.wants ] || mkdir -p ${PREFIX}/etc/systemd/system/initrd.target.wants
            ln -s ../${_name}.device ${PREFIX}/etc/systemd/system/initrd.target.wants/${_name}.device
            type mark_hostonly >/dev/null 2>&1 && mark_hostonly /etc/systemd/system/initrd.target.wants/${_name}.device
            _needreload=1
        fi

if ! [ -f ${PREFIX}/etc/systemd/system/${_name}.device.d/timeout.conf ]; then
            mkdir -p ${PREFIX}/etc/systemd/system/${_name}.device.d
            {
                echo "[Unit]"
                echo "JobTimeoutSec=$_timeout"
                echo "JobRunningTimeoutSec=$_timeout"
            } > ${PREFIX}/etc/systemd/system/${_name}.device.d/timeout.conf
            type mark_hostonly >/dev/null 2>&1 && mark_hostonly /etc/systemd/system/${_name}.device.d/timeout.conf
            _needreload=1
        fi

if [ -z "$PREFIX" ] && [ "$_needreload" = 1 ] && [ -z "$_noreload" ]; then
            /sbin/initqueue --onetime --unique --name daemon-reload systemctl daemon-reload
        fi
    fi
}
# wait_for_dev <dev>
#
# Installs a initqueue-finished script,
# which will cause the main loop only to exit,
# if the device <dev> is recognized by the system.
wait_for_dev()
{
    local _name
    local _noreload

if [ "$1" = "-n" ]; then
        _noreload=-n
        shift
    fi

_name="$(str_replace "$1" '/' '\x2f')"

type mark_hostonly >/dev/null 2>&1 && mark_hostonly "$hookdir/initqueue/finished/devexists-${_name}.sh"

[ -e "${PREFIX}$hookdir/initqueue/finished/devexists-${_name}.sh" ] && return 0

printf '[ -e "%s" ]\n' $1 \
        >> "${PREFIX}$hookdir/initqueue/finished/devexists-${_name}.sh"
    {
        printf '[ -e "%s" ] || ' $1
        printf 'warn "\"%s\" does not exist"\n' $1
    } >> "${PREFIX}$hookdir/emergency/80-${_name}.sh"

set_systemd_timeout_for_dev $_noreload $1
}

cancel_wait_for_dev()
{
    local _name
    _name="$(str_replace "$1" '/' '\x2f')"
    rm -f -- "$hookdir/initqueue/finished/devexists-${_name}.sh"
    rm -f -- "$hookdir/emergency/80-${_name}.sh"
    if [ -n "$DRACUT_SYSTEMD" ]; then
        _name=$(dev_unit_name "$1")
        rm -f -- ${PREFIX}/etc/systemd/system/initrd.target.wants/${_name}.device
        rm -f -- ${PREFIX}/etc/systemd/system/${_name}.device.d/timeout.conf
        /sbin/initqueue --onetime --unique --name daemon-reload systemctl daemon-reload
    fi
}

killproc() {
    debug_off
    local _exe="$(command -v $1)"
    local _sig=$2
    local _i
    [ -x "$_exe" ] || return 1
    for _i in /proc/[0-9]*; do
        [ "$_i" = "/proc/1" ] && continue
        if [ -e "$_i"/_exe ] && [  "$_i/_exe" -ef "$_exe" ] ; then
            kill $_sig ${_i##*/}
        fi
    done
    debug_on
}

need_shutdown() {
    >/run/initramfs/.need_shutdown
}

wait_for_loginit()
{
    [ "$RD_DEBUG" = "yes" ] || return
    [ -e /run/initramfs/loginit.pipe ] || return
    debug_off
    echo "DRACUT_LOG_END"
    exec 0<>/dev/console 1<>/dev/console 2<>/dev/console
        # wait for loginit
    i=0
    while [ $i -lt 10 ]; do
        if [ ! -e /run/initramfs/loginit.pipe ]; then
            j=$(jobs)
            [ -z "$j" ] && break
            [ -z "${j##*Running*}" ] || break
        fi
        sleep 0.1
        i=$(($i+1))
    done

if [ $i -eq 10 ]; then
        kill %1 >/dev/null 2>&1
        kill $(while read line || [ -n "$line" ];do echo $line;done</run/initramfs/loginit.pid)
    fi

setdebug
    rm -f -- /run/initramfs/loginit.pipe /run/initramfs/loginit.pid
}

# pidof version for root
if ! command -v pidof >/dev/null 2>/dev/null; then
    pidof() {
        debug_off
        local _cmd
        local _exe
        local _rl
        local _ret=1
        local i
        _cmd="$1"
        if [ -z "$_cmd" ]; then
            debug_on
            return 1
        fi
        _exe=$(command -v "$1")
        for i in /proc/*/exe; do
            [ -e "$i" ] || continue
            if [ -n "$_exe" ]; then
                [ "$i" -ef "$_exe" ] || continue
            else
                _rl=$(readlink -f "$i");
                [ "${_rl%/$_cmd}" != "$_rl" ] || continue
            fi
            i=${i%/exe}
            echo ${i##/proc/}
            _ret=0
        done
        debug_on
        return $_ret
    }
fi

_emergency_shell()
{
    local _name="$1"
    if [ -n "$DRACUT_SYSTEMD" ]; then
        > /.console_lock
        echo "PS1=\"$_name:\\\${PWD}# \"" >/etc/profile
        systemctl start dracut-emergency.service
        rm -f -- /etc/profile
        rm -f -- /.console_lock
    else
        debug_off
        source_hook "$hook"
        echo
        /sbin/rdsosreport
        echo 'You might want to save "/run/initramfs/rdsosreport.txt" to a USB stick or /boot'
        echo 'after mounting them and attach it to a bug report.'
        if ! RD_DEBUG= getargbool 0 rd.debug -d -y rdinitdebug -d -y rdnetdebug; then
            echo
            echo 'To get more debug information in the report,'
            echo 'reboot with "rd.debug" added to the kernel command line.'
        fi
        echo
        echo 'Dropping to debug shell.'
        echo
        export PS1="$_name:\${PWD}# "
        [ -e /.profile ] || >/.profile

_ctty="$(RD_DEBUG= getarg rd.ctty=)" && _ctty="/dev/${_ctty##*/}"
        if [ -z "$_ctty" ]; then
            _ctty=console
            while [ -f /sys/class/tty/$_ctty/active ]; do
                _ctty=$(cat /sys/class/tty/$_ctty/active)
                _ctty=${_ctty##* } # last one in the list
            done
            _ctty=/dev/$_ctty
        fi
        [ -c "$_ctty" ] || _ctty=/dev/tty1
        case "$(/usr/bin/setsid --help 2>&1)" in *--ctty*) CTTY="--ctty";; esac
        setsid $CTTY /bin/sh -i -l 0<>$_ctty 1<>$_ctty 2<>$_ctty
    fi
}

emergency_shell()
{
    local _ctty
    set +e
    local _rdshell_name="dracut" action="Boot" hook="emergency"
    local _emergency_action

if [ "$1" = "-n" ]; then
        _rdshell_name=$2
        shift 2
    elif [ "$1" = "--shutdown" ]; then
        _rdshell_name=$2; action="Shutdown"; hook="shutdown-emergency"
        if type plymouth >/dev/null 2>&1; then
            plymouth --hide-splash
        elif [ -x /oldroot/bin/plymouth ]; then
            /oldroot/bin/plymouth --hide-splash
        fi
        shift 2
    fi

echo ; echo
    warn "$*"
    echo

_emergency_action=$(getarg rd.emergency)
    [ -z "$_emergency_action" ] \
        && [ -e /run/initramfs/.die ] \
        && _emergency_action=halt

if getargbool 1 rd.shell -d -y rdshell || getarg rd.break -d rdbreak; then
        _emergency_shell $_rdshell_name
    else
        source_hook "$hook"
        warn "$action has failed. To debug this issue add \"rd.shell rd.debug\" to the kernel command line."
        [ -z "$_emergency_action" ] && _emergency_action=halt
    fi

case "$_emergency_action" in
        reboot)
            reboot || exit 1;;
        poweroff)
            poweroff || exit 1;;
        halt)
            halt || exit 1;;
    esac
}

# Retain the values of these variables but ensure that they are unexported
# This is a POSIX-compliant equivalent of bash's "export -n"
export_n()
{
    local var
    local val
    for var in "$@"; do
        eval val=\$$var
        unset $var
        [ -n "$val" ] && eval $var=\"$val\"
    done
}

# returns OK if list1 contains all elements of list2, i.e. checks if list2 is a
# sublist of list1.  An order and a duplication doesn't matter.
#
# $1 = separator
# $2 = list1
# $3 = list2
# $4 = ignore values, separated by $1
listlist() {
    local _sep="$1"
    local _list="${_sep}${2}${_sep}"
    local _sublist="$3"
    [ -n "$4" ] && local _iglist="${_sep}${4}${_sep}"
    local IFS="$_sep"
    local _v

[ "$_list" = "$_sublist" ] && return 0

for _v in $_sublist; do
        if [ -n "$_v" ] && ! ( [ -n "$_iglist" ] && strstr "$_iglist" "$_v" )
        then
            strstr "$_list" "$_v" || return 1
        fi
    done

return 0
}

# returns OK if both lists contain the same values.  An order and a duplication
# doesn't matter.
#
# $1 = separator
# $2 = list1
# $3 = list2
# $4 = ignore values, separated by $1
are_lists_eq() {
    listlist "$1" "$2" "$3" "$4" && listlist "$1" "$3" "$2" "$4"
}

setmemdebug() {
    if [ -z "$DEBUG_MEM_LEVEL" ]; then
        export DEBUG_MEM_LEVEL=$(getargnum 0 0 5 rd.memdebug)
    fi
}

setmemdebug

# parameters: func log_level prefix msg [trace_level:trace]...
make_trace_mem()
{
    local log_level prefix msg msg_printed
    local trace trace_level trace_in_higher_levels insert_trace

msg=$1
    shift

prefix='[debug_mem]'
    log_level=$DEBUG_MEM_LEVEL

if [ -z "$log_level" ] || [ "$log_level" -le 0 ]; then
        return
    fi

msg=$(echo $msg)

msg_printed=0
    while [ $# -gt 0 ]; do
        trace=${1%%:*}
        trace_level=${trace%%+}
        [ "$trace" != "$trace_level" ] && trace_in_higher_levels="yes"
        trace=${1##*:}

if [ -z "$trace_level" ]; then
            trace_level=0
        fi

insert_trace=0
        if [ -n "$trace_in_higher_levels" ]; then
            if [ "$log_level" -ge "$trace_level" ]; then
                insert_trace=1
            fi
        else
            if [ "$log_level" -eq "$trace_level" ]; then
                insert_trace=1
            fi
        fi

if [ $insert_trace -eq 1 ]; then
            if [ $msg_printed -eq 0 ]; then
                echo "$prefix $msg"
                msg_printed=1
            fi
            show_memstats $trace
        fi
        shift
    done
}

# parameters: type
show_memstats()
{
    case $1 in
        shortmem)
            cat /proc/meminfo  | grep -e "^MemFree" -e "^Cached" -e "^Slab"
            ;;
        mem)
            cat /proc/meminfo
            ;;
        slab)
            cat /proc/slabinfo
            ;;
        iomem)
            cat /proc/iomem
            ;;
    esac
}

remove_hostonly_files() {
    rm -fr /etc/cmdline /etc/cmdline.d/*.conf "$hookdir/initqueue/finished"
    if [ -f /lib/dracut/hostonly-files ]; then
        while read line || [ -n "$line" ]; do
            [ -e "$line" ] || [ -h "$line" ] || continue
            rm -f "$line"
        done < /lib/dracut/hostonly-files
    fi
}

Name	Type	Size	Owner/Group	Permission	Last Modified	Actions
.	dir	-	root/root	0755	2025-09-09 12:44:01
..	dir	-	root/root	0755	2025-07-15 09:09:28
dracut-lib.sh	file	32.96 KB	root/root	0755	2025-07-15 09:09:22
init.sh	file	11.52 KB	root/root	0755	2025-07-15 09:09:21
initqueue.sh	file	1.14 KB	root/root	0755	2018-10-08 01:38:33
loginit.sh	file	492 B	root/root	0755	2018-10-08 01:38:33
module-setup.sh	file	4.01 KB	root/root	0755	2025-07-15 09:09:21
parse-root-opts.sh	file	246 B	root/root	0755	2018-10-08 01:38:33
rdsosreport.sh	file	1.31 KB	root/root	0755	2018-10-08 01:38:33

For more Private tool come to me!

https://t.me/aDriv4vz